NanoKontrol 2 MIDI Remote Script: "APC Emulation"
Re: NanoKontrol 2 MIDI Remote Script: "APC Emulation"
Wait, are these scripts working for you guys in live 9.1.7??
I always used and created midi remote scripts in live 8, but i can't get anything to run correctly with this version anymore...
I always used and created midi remote scripts in live 8, but i can't get anything to run correctly with this version anymore...
Re: NanoKontrol 2 MIDI Remote Script: "APC Emulation"
Yes, it does work. You first need to use the Korg editor (download from their website) to reassign the nanoKONTROL2 to run in MIDI CC mode, then remap the MIDI CCs as laid out in the first page of this thread. Then follow the instructions for installing the remote script, and setting your MIDI preferences in Live. It took me a while, but if you read through the whole thread, all the info on how to get it working is available.SvenDer wrote:Wait, are these scripts working for you guys in live 9.1.7??
I always used and created midi remote scripts in live 8, but i can't get anything to run correctly with this version anymore...
Re: NanoKontrol 2 MIDI Remote Script: "APC Emulation"
Hi,EarHax wrote:Yes, it does work. You first need to use the Korg editor (download from their website) to reassign the nanoKONTROL2 to run in MIDI CC mode, then remap the MIDI CCs as laid out in the first page of this thread. Then follow the instructions for installing the remote script, and setting your MIDI preferences in Live. It took me a while, but if you read through the whole thread, all the info on how to get it working is available.SvenDer wrote:Wait, are these scripts working for you guys in live 9.1.7??
I always used and created midi remote scripts in live 8, but i can't get anything to run correctly with this version anymore...
thanks for the tips. I did all the steps multiple times, it just doesn't seem to work... Too bad
Re: NanoKontrol 2 MIDI Remote Script: "APC Emulation"
Hi there, I've got two questions concerning the script...
first of all I would like to know where I can change the maximum value of the faders that control the mixer volumes in Live. I would like to change the script in that way that the volume for each channel only goes up to a maximum of around 0 dB in Live. (However this cannot be done by Live's MIDI allocation table as this would limit the amount of usable channels, as far as I tested).
Secondly I want to change the faders and knobs behavior in the alt mode like this:
fader 1 - pitch (should have some "space" or buffer around value 64, so that it is easier to bring the fader back in its zero pitch position (e. g: fader should only react on values above 70 or under 58)
fader 2 - mod wheel (same as cc1??)
fader 3 - aftertouch
fader 4 - velocity
fader 5 - cc2 (breathe)
fader 6 - cc11 (expression)
fader 7 - cc64 (sustain)
fader 8 - cc7 volume
knob 1 - cc8 (balance)
knob 2 - cc10 (pan)
knob 3 - cc70 (sound variation)
knob 4 - cc71 (filter cutoff/harmonic)
knob 5 - cc72 (release time)
knob 6 - cc73 (attack time)
knob 7 - cc74 (brightness/resonance)
knob 8 - cc84 (portamento)
All of the above values should be editable and therefore be placed in an extra file in the script folder.
Would someone be willing and able programming these ideas in the original dynamiiic script and send it to me via private message?? That would be awesome! Unfortunately I've got no clue of how to program in Python language... it's a pity
first of all I would like to know where I can change the maximum value of the faders that control the mixer volumes in Live. I would like to change the script in that way that the volume for each channel only goes up to a maximum of around 0 dB in Live. (However this cannot be done by Live's MIDI allocation table as this would limit the amount of usable channels, as far as I tested).
Secondly I want to change the faders and knobs behavior in the alt mode like this:
fader 1 - pitch (should have some "space" or buffer around value 64, so that it is easier to bring the fader back in its zero pitch position (e. g: fader should only react on values above 70 or under 58)
fader 2 - mod wheel (same as cc1??)
fader 3 - aftertouch
fader 4 - velocity
fader 5 - cc2 (breathe)
fader 6 - cc11 (expression)
fader 7 - cc64 (sustain)
fader 8 - cc7 volume
knob 1 - cc8 (balance)
knob 2 - cc10 (pan)
knob 3 - cc70 (sound variation)
knob 4 - cc71 (filter cutoff/harmonic)
knob 5 - cc72 (release time)
knob 6 - cc73 (attack time)
knob 7 - cc74 (brightness/resonance)
knob 8 - cc84 (portamento)
All of the above values should be editable and therefore be placed in an extra file in the script folder.
Would someone be willing and able programming these ideas in the original dynamiiic script and send it to me via private message?? That would be awesome! Unfortunately I've got no clue of how to program in Python language... it's a pity
Re: NanoKontrol 2 MIDI Remote Script: "APC Emulation"
Hi Sven!SvenDer wrote:Hi,EarHax wrote:Yes, it does work. You first need to use the Korg editor (download from their website) to reassign the nanoKONTROL2 to run in MIDI CC mode, then remap the MIDI CCs as laid out in the first page of this thread. Then follow the instructions for installing the remote script, and setting your MIDI preferences in Live. It took me a while, but if you read through the whole thread, all the info on how to get it working is available.SvenDer wrote:Wait, are these scripts working for you guys in live 9.1.7??
I always used and created midi remote scripts in live 8, but i can't get anything to run correctly with this version anymore...
thanks for the tips. I did all the steps multiple times, it just doesn't seem to work... Too bad
What is exactly your problem?
Script folder doesn't show up in the list? Script doesn't load?
Re: NanoKontrol 2 MIDI Remote Script: "APC Emulation"
Hi everyone,
I can't get to work this script in live 9.1.8 please help...
1. I have installed the script into the correct folder, also using channel 3 (as my APC already uses channel 1) - to do this, I've changed the constant CHANNEL = 2 (because channels are 0 - 15) in the consts.py
2. I have edited KORG KONTROL EDITOR and written on the nanokontrol 2, using the channel 3.
3. I have followed instructions for LIVE MIDI SYNC preferences. The script comes out in the list, but just doesn't work in live. I can only assign to mappings.
4. I would ultimately love to have PUSH and NanoKonrol sync, like mentioned in this thread a few pages ago.
Any help will be appreciated!
I can't get to work this script in live 9.1.8 please help...
1. I have installed the script into the correct folder, also using channel 3 (as my APC already uses channel 1) - to do this, I've changed the constant CHANNEL = 2 (because channels are 0 - 15) in the consts.py
2. I have edited KORG KONTROL EDITOR and written on the nanokontrol 2, using the channel 3.
3. I have followed instructions for LIVE MIDI SYNC preferences. The script comes out in the list, but just doesn't work in live. I can only assign to mappings.
4. I would ultimately love to have PUSH and NanoKonrol sync, like mentioned in this thread a few pages ago.
Any help will be appreciated!
Re: NanoKontrol 2 MIDI Remote Script: "APC Emulation"
Hi xfechx, post here your log.txt!xfechx wrote:Hi everyone,
I can't get to work this script in live 9.1.8 please help...
Re: NanoKontrol 2 MIDI Remote Script: "APC Emulation"
Definitely, where can I find the log.txt?dynamiiic wrote:Hi xfechx, post here your log.txt!xfechx wrote:Hi everyone,
I can't get to work this script in live 9.1.8 please help...
Thanks!!
Re: NanoKontrol 2 MIDI Remote Script: "APC Emulation"
xfechx wrote:Definitely, where can I find the log.txt?dynamiiic wrote:Hi xfechx, post here your log.txt!xfechx wrote:Hi everyone,
I can't get to work this script in live 9.1.8 please help...
Thanks!!
Are you a mac user? If so, you can find at /Users/yourusername/Library/Preferences/Ableton/Live yourversion/Log.txt
In windows I can't remember it, just google a bit and you'll find it
-
- Posts: 5
- Joined: Tue Apr 28, 2015 10:32 am
Re: NanoKontrol 2 MIDI Remote Script: "APC Emulation"
Hey maybe this is old news already. Looks like a great script! I don't suppose anyone knows if this is supposed to work in 9.2? I followed the instruction exactly like 4 times (I'm a decent user, long-time midi guy, had the nanoKontrol for a while, edited it many times). The script never comes up in the control surfaces drop-down list. Quit Live, do it all over again, etc etc etc. Nothing. Any clues?
Re: NanoKontrol 2 MIDI Remote Script: "APC Emulation"
I own a Xone K2. Can I alter this script easy so that I can use it with that device.
All i need is the send up and down actually. Thanks!!
All i need is the send up and down actually. Thanks!!
-
- Posts: 6025
- Joined: Mon May 15, 2006 12:15 pm
Re: NanoKontrol 2 MIDI Remote Script: "APC Emulation"
Hey,
does the NanoKontrol 2 respond to incoming CCs to switch the lights on and off ?
thanks
does the NanoKontrol 2 respond to incoming CCs to switch the lights on and off ?
thanks
MacBook Pro 13" Retina i7 2.8 GHz OS 10.13, L10.0.1, M4L.
MacStudio M1Max 32Go OS 12.3.1
MacStudio M1Max 32Go OS 12.3.1
Re: NanoKontrol 2 MIDI Remote Script: "APC Emulation"
Hi Tim,timkdj wrote:I own a Xone K2. Can I alter this script easy so that I can use it with that device.
All i need is the send up and down actually. Thanks!!
We've released a Control Surface Script for the K2 which gives the Red Box functionality, it can't be programmed by general convention due to the latching layers...
http://isotonikstudios.com/sigabort/allen-heath-k1-k2/
Cheers
D
Re: NanoKontrol 2 MIDI Remote Script: "APC Emulation"
Hey Eli, pls send me your log file /Users/yourusername/Library/Preferences/Ableton/Live yourversion/Log.txt - Assuming you're on OSXEli Salzman wrote:Hey maybe this is old news already. Looks like a great script! I don't suppose anyone knows if this is supposed to work in 9.2? I followed the instruction exactly like 4 times (I'm a decent user, long-time midi guy, had the nanoKontrol for a while, edited it many times). The script never comes up in the control surfaces drop-down list. Quit Live, do it all over again, etc etc etc. Nothing. Any clues?