Assigning footswitch ports?
-
- Posts: 70
- Joined: Tue Jan 06, 2009 11:32 pm
- Location: Portsmouth, NH
Assigning footswitch ports?
I'm trying to set up my footswitch ports but I'm not having any success. I'd like to set up my sustain pedal so that it works with the instruments I'm playing in Note mode, and I'd like to use my expression pedal so that I can map it to other Live controls. There is a lack of any info about the footswitch ports in the manual so I can't tell where I might be missing something.....
The pedals are both the correct polarity. When I use each pedal I see Live's MIDI Indicator light flash, and moreover, when in User mode I can map both to whatever I want within Live, so I know that things are working somewhat correctly. How do I setup each port to work with Push in Note mode (or non-User mode in general) ?
The pedals are both the correct polarity. When I use each pedal I see Live's MIDI Indicator light flash, and moreover, when in User mode I can map both to whatever I want within Live, so I know that things are working somewhat correctly. How do I setup each port to work with Push in Note mode (or non-User mode in general) ?
Re: Assigning footswitch ports?
im pretty sure that they are just switches, not cc. I dont think your expression pedal will work with them.
-
- Posts: 70
- Joined: Tue Jan 06, 2009 11:32 pm
- Location: Portsmouth, NH
Re: Assigning footswitch ports?
I hope that's not the case but it may be so. They do work properly in User mode though so I can't see why I shouldn't be able to get at least the sustain pedal to work with instruments I'm playing in Note mode.
Why they aren't addressed in the manual is a bit of a head-scratcher...
Why they aren't addressed in the manual is a bit of a head-scratcher...
-
- Posts: 45
- Joined: Tue Jul 08, 2003 1:01 am
- Location: international!
- Contact:
Re: Assigning footswitch ports?
The outer one is for hold (sustain), inner for record toggle.
I don't believe they can be reassigned in native mode... (i'm probably wrong).
I don't believe they can be reassigned in native mode... (i'm probably wrong).
-
- Posts: 70
- Joined: Tue Jan 06, 2009 11:32 pm
- Location: Portsmouth, NH
Re: Assigning footswitch ports?
OK, that makes sense, and I'm fine not being able to reassign anything in Native mode, but I still can't get either jack to do anything unless Push is in User mode.corporation wrote:The outer one is for hold (sustain), inner for record toggle.
I don't believe they can be reassigned in native mode... (i'm probably wrong).
When I plug my sustain pedal into the outside jack, it doesn't actually do anything at all in Native mode. Works great in User mode, though, as does my expression pedal...
Re: Assigning footswitch ports?
^ Ok, just so I understand what you're saying, if I put Push in User Mode, then I can use FS2 for Looper and to toggle recoding in clips? Because as of now, in Native mode, neither port does anything.
On the APC40, my footswitch in FS2 was brilliant for live looping guitars into clips, but I can't seem to do it with Push. If any has suggestions, lemme know.
On the APC40, my footswitch in FS2 was brilliant for live looping guitars into clips, but I can't seem to do it with Push. If any has suggestions, lemme know.
-
- Posts: 70
- Joined: Tue Jan 06, 2009 11:32 pm
- Location: Portsmouth, NH
Re: Assigning footswitch ports?
That seems to be what Corporation is saying but I can't get it to work either. Is there a settings menu or something where the footswitch ports need to be activated before they can be used? Anyone successfully using the ports in Native mode?nebulae wrote:^ Ok, just so I understand what you're saying, if I put Push in User Mode, then I can use FS2 for Looper and to toggle recoding in clips? Because as of now, in Native mode, neither port does anything.
On the APC40, my footswitch in FS2 was brilliant for live looping guitars into clips, but I can't seem to do it with Push. If any has suggestions, lemme know.
Re: Assigning footswitch ports?
I can assign the footswitches in User mode to individual clips, but it does not work like it does on the APC40 FS2, where a press can be a clip launch. It doesn't do that with Push.
So what I'm still trying to figure out is how you would use a footswitch to work with looper.
So what I'm still trying to figure out is how you would use a footswitch to work with looper.
Re: Assigning footswitch ports?
when using my sustain pedal with live i can confirm:
live mode:
port 1: pedal outputs cc 64 (127 when pressed, 0 when not pressed), midi channel 1. the pedal acts as a sustain pedal when live is in note mode.
port 2: pedal outputs cc 69 (127 when pressed, 0 when not pressed), midi channel 1. right off the bat, can't seem to figure out what this could be mapped to when in live mode with push.
user mode: outputs the same midi data as when push is in live mode. also works as sustain pedal when playing any track.
live mode:
port 1: pedal outputs cc 64 (127 when pressed, 0 when not pressed), midi channel 1. the pedal acts as a sustain pedal when live is in note mode.
port 2: pedal outputs cc 69 (127 when pressed, 0 when not pressed), midi channel 1. right off the bat, can't seem to figure out what this could be mapped to when in live mode with push.
user mode: outputs the same midi data as when push is in live mode. also works as sustain pedal when playing any track.
-
- Posts: 70
- Joined: Tue Jan 06, 2009 11:32 pm
- Location: Portsmouth, NH
Re: Assigning footswitch ports?
It's really strange, but now my sustain pedal is working while in Note mode when plugged into Port 1. OK, just going to accept it....coleb wrote:when using my sustain pedal with live i can confirm:
live mode:
port 1: pedal outputs cc 64 (127 when pressed, 0 when not pressed), midi channel 1. the pedal acts as a sustain pedal when live is in note mode.
port 2: pedal outputs cc 69 (127 when pressed, 0 when not pressed), midi channel 1. right off the bat, can't seem to figure out what this could be mapped to when in live mode with push.
user mode: outputs the same midi data as when push is in live mode. also works as sustain pedal when playing any track.
Re: Assigning footswitch ports?
^ This is all very bizarre behavior. The FS1 and FS2 issues need to be resolved. I can't figure out how to use Looper in Live mode, which seems to be a missing functionality. I will email support@ableton about it.
Re: Assigning footswitch ports?
has anybody figured it out yet? i'm trying to use my footswitch to toggle the session record button, but i can't seem to get it to do anything (except in user mode).
Re: Assigning footswitch ports?
One obvious thing I just discovered; I bought a M-Audio switchable polarity for the sutain ped on Push - it works great. However, today I noticed that the sustain pedal of my RD-700 piano works with both the RD & Push while plugged to the RD.
http://www.iam-pcr.com
Live 9, Push, MountainLion
Live 9, Push, MountainLion
Re: Assigning footswitch ports?
I'm also interested on an answers, will you post the answer from support?nebulae wrote:Send a request to support.