.
-
- Posts: 29
- Joined: Sat May 29, 2010 8:31 am
Re: Headroom
No difference.
You understand headroom correctly, it really is the db gap left between 0db and your highest peaks once the track has played through. Live's meter will show this as the -db figure in the top indicator next to the meter.
Norm would be to leave around 3db headroom for the mastering engineer to play around with, if you are just mixing down you can use this headroom to boost your own level using a limiter for example to get your mixdown to a reasonable volume for playback.
You understand headroom correctly, it really is the db gap left between 0db and your highest peaks once the track has played through. Live's meter will show this as the -db figure in the top indicator next to the meter.
Norm would be to leave around 3db headroom for the mastering engineer to play around with, if you are just mixing down you can use this headroom to boost your own level using a limiter for example to get your mixdown to a reasonable volume for playback.
-
- Posts: 8803
- Joined: Wed Mar 31, 2004 3:12 pm
- Location: www.fridge.net.au
- Contact:
Re: Headroom
Here's what I don't get about headroom in the digital world...
Why would a mastering engineer need us to turn down a mix and give him 3db (which I usually do by chucking a Utility plugin on the master and taking it down a few db), instead of doing so themselves using a trim/gain reduction plugin?
I understand in the old days it was about making sure you don't raise the noise floor from tape etc.. but these days as long as there's no clipping, the headroom shouldn't matter, no?
Why would a mastering engineer need us to turn down a mix and give him 3db (which I usually do by chucking a Utility plugin on the master and taking it down a few db), instead of doing so themselves using a trim/gain reduction plugin?
I understand in the old days it was about making sure you don't raise the noise floor from tape etc.. but these days as long as there's no clipping, the headroom shouldn't matter, no?
Re: Headroom
When we ask for lower mixes (I usually as for -6dBFS) is just to make sure we get a file that is not clipping in any way. The actual number doesn't matter, it's just to insure that people aren't mistakenly (or not) clipping the master channel in their DAW before rendering. For most experienced musicians, it's an obvious thing "don't clip, duh". But you'd be surpised at how often we get sent stuff that's obviously clipping bad, but the artist didn't hear it.
tarekith
https://tarekith.com
https://tarekith.com
-
- Posts: 799
- Joined: Thu May 28, 2009 4:19 am
- Location: LA
Re: Headroom
AHA. I have also wondered this for a long time. So there is no other benefit sonically to say, mixing with a 3 (or 6) db headroom and then mastering?Tarekith wrote:When we ask for lower mixes (I usually as for -6dBFS) is just to make sure we get a file that is not clipping in any way. The actual number doesn't matter, it's just to insure that people aren't mistakenly (or not) clipping the master channel in their DAW before rendering. For most experienced musicians, it's an obvious thing "don't clip, duh". But you'd be surpised at how often we get sent stuff that's obviously clipping bad, but the artist didn't hear it.
BTW, I have read your mixing/leveling/mastering tutorials Tarekith, and they are great btw, this is just always something I wondered.
https://soundcloud.com/unearthproductions
beats me wrote:everybody around you thinks you’re a fucking idiot.
Re: Headroom
No, there's no real difference sonically between -3dB and -6dB. It's just a safety net if you will.DangerousDave wrote:AHA. I have also wondered this for a long time. So there is no other benefit sonically to say, mixing with a 3 (or 6) db headroom and then mastering?
tarekith
https://tarekith.com
https://tarekith.com
-
- Posts: 6659
- Joined: Sun Nov 19, 2006 1:56 am
- Location: greater toronto area
Re: Headroom
You still need to watch levels even if your peak ceiling is -3dBFS instead of 0dbFS, if you send a hypercompressed file with a peak of -3 or -6dbFS it will still sound clipped/distorted and the mastering stage won't be able to make it sound a lot better - some tools, such as certain expanders (called de-compressors) can help a little but aren't a magic cure - you need some transients in your music for it to sound punchy, otherwise it's one big AAAAAAAAAARRRRRRRRRGGGGGHHHHHHH.
Some people still whack on the gain and have high RMS levels with hypercompressing and think because the peak level is -3dBFS they are fine - No. Less is more in terms of sound quality at the mix stage. Having a limiter flat top all your audio files at -3dbFS is not a good solution.
IN the mix, I always try and leave at least 5dB of headroom in the master, and don't use a limiter on the master in most instances (I use a meter like SPAN to make sure I'm not going above the -5dB and reduce the channels if necessary), I sometimes use a limiter on the drum buss because fast transients occur on many percussion instruments and drums.
Some people still whack on the gain and have high RMS levels with hypercompressing and think because the peak level is -3dBFS they are fine - No. Less is more in terms of sound quality at the mix stage. Having a limiter flat top all your audio files at -3dbFS is not a good solution.
IN the mix, I always try and leave at least 5dB of headroom in the master, and don't use a limiter on the master in most instances (I use a meter like SPAN to make sure I'm not going above the -5dB and reduce the channels if necessary), I sometimes use a limiter on the drum buss because fast transients occur on many percussion instruments and drums.
http://soundcloud.com/umbriel-rising http://www.myspace.com/leedsquietmandemos Live 7.0.18 SUITE, Cubase 5.5.2], Soundforge 9, Dell XPS M1530, 2.2 Ghz C2D, 4GB, Vista Ult SP2, legit plugins a plenty, Alesis IO14.
-
- Posts: 518
- Joined: Mon May 18, 2009 5:33 pm
Re: Headroom
I turn down all faders of all tracks together, till I get -5or6dB...!
Is this O.K. too...???
How loud should a single track be...?
Some people go for -12 some -18, but I also have read that
some others go for 0dB and then turn the master down to around -6dB.
Which way is the best ???
I would like to clear this out once and for all...
Thank You...
Is this O.K. too...???
How loud should a single track be...?
Some people go for -12 some -18, but I also have read that
some others go for 0dB and then turn the master down to around -6dB.
Which way is the best ???
I would like to clear this out once and for all...
Thank You...
No! I'll never use the Push-App Live 9 !!!
Re: Headroom
Leave the master fader at 0dBFS, and turn down the channel faders until the master meter is peaking around -6dBFS.
tarekith
https://tarekith.com
https://tarekith.com
-
- Posts: 518
- Joined: Mon May 18, 2009 5:33 pm
Re: Headroom
Thanks I keep doing this...!
...but what do you think about the other way...?
Making sounds loud to 0dB and then going to turn the fader down on the master,
till you reach -6dB.
Maybe not with the fader but with an utility tool.
In the end you get also the level at the needed value.
But is this any different in any way...?
I would like to know what you think about this way, Tarekith.
...but what do you think about the other way...?
Making sounds loud to 0dB and then going to turn the fader down on the master,
till you reach -6dB.
Maybe not with the fader but with an utility tool.
In the end you get also the level at the needed value.
But is this any different in any way...?
I would like to know what you think about this way, Tarekith.
No! I'll never use the Push-App Live 9 !!!
Re: Headroom
As long as you're not pulling the master fader down more than 3-6dB, I don't think it's a big issue. I personally like leaving it at 0 as then I always have a reference point, but you don't HAVE to.
tarekith
https://tarekith.com
https://tarekith.com
-
- Posts: 6659
- Joined: Sun Nov 19, 2006 1:56 am
- Location: greater toronto area
Re: Headroom
For the reason I mentioned in the last post.
Should you ever work on an analogue console it is also good practice to leave the master fader at unity gain (0dB) and reduce the individual track channels and/or group busses. Also on a Protools HD rig, this analogue approach is recommended because it uses a fixed point calculation on it's DSP chips, as opposed to 32 bit floating point. So it's a better habit to do things this way, old fogeys like me who were brought up on analogue consoles and analogue tape appreciate this, you younger guys who have only known digital are tempted to just hit the master fader, on 32 bit float this is acceptable but it's a bit of an easy way out and would kill your headroom in analogue systems and while not kill, it would degrade sound quality a bit in a DSP based rig with fixed point processing, such as Protools HD, Pyramix DSP, SaDie, etc.
Should you ever work on an analogue console it is also good practice to leave the master fader at unity gain (0dB) and reduce the individual track channels and/or group busses. Also on a Protools HD rig, this analogue approach is recommended because it uses a fixed point calculation on it's DSP chips, as opposed to 32 bit floating point. So it's a better habit to do things this way, old fogeys like me who were brought up on analogue consoles and analogue tape appreciate this, you younger guys who have only known digital are tempted to just hit the master fader, on 32 bit float this is acceptable but it's a bit of an easy way out and would kill your headroom in analogue systems and while not kill, it would degrade sound quality a bit in a DSP based rig with fixed point processing, such as Protools HD, Pyramix DSP, SaDie, etc.
http://soundcloud.com/umbriel-rising http://www.myspace.com/leedsquietmandemos Live 7.0.18 SUITE, Cubase 5.5.2], Soundforge 9, Dell XPS M1530, 2.2 Ghz C2D, 4GB, Vista Ult SP2, legit plugins a plenty, Alesis IO14.