Cover for Push 2
-
- Posts: 8
- Joined: Fri Nov 06, 2015 1:31 pm
Cover for Push 2
Hi,
anyone know if there is a dust cover out for Push 2?
anyone know if there is a dust cover out for Push 2?
Re: Cover for Push 2
im sure Decksaver will make one soon, right now im using the grey top of the push package as dust cover :)
Re: Cover for Push 2
decksaver said on their fb page that they are on it
Re: Cover for Push 2
I just take the cotton cover I had for my MPC2500 (bought from mpcstuff.com), works fine for me. Since I have the push2 I putted the MPC back in the original Box
Re: Cover for Push 2
im steering clear of decksaver this time round i suspect it was the tight fit of the decksaver cover that eroded the rubber coating off the first push i had
-
- Posts: 8
- Joined: Fri Nov 06, 2015 1:31 pm
Re: Cover for Push 2
thanks everyone!
Personally I would love to get my hands on this one:
http://savedbytechnology.com/catalog/ne ... ush_05.jpg
But Ableton says they stopped producing them...
Personally I would love to get my hands on this one:
http://savedbytechnology.com/catalog/ne ... ush_05.jpg
But Ableton says they stopped producing them...
Re: Cover for Push 2
I wonder if I was just lucky with my Push. I used it almost every day for around 2 years, and every day the Decksaver cover would be taken on and off. It still looks brand new, apart from some faint spots of some dried liquid on one side which can only be seen from certain angles - probably the spray of cans as they were opened.ash1 wrote:im steering clear of decksaver this time round i suspect it was the tight fit of the decksaver cover that eroded the rubber coating off the first push i had
No rubber coating has come off anywhere.
Re: Cover for Push 2
i dont know maybe you were lucky all i know is the decksaver eroded the rubber on mine
my lesson learned
i will pass on the decksaver this time round and see what else comes out
my lesson learned
i will pass on the decksaver this time round and see what else comes out
Re: Cover for Push 2
I didn't use mine every day, but I never had any issues with my decksaver doing that either. I could definitely see it being an issue though.tedlogan wrote:I wonder if I was just lucky with my Push. I used it almost every day for around 2 years, and every day the Decksaver cover would be taken on and off. It still looks brand new, apart from some faint spots of some dried liquid on one side which can only be seen from certain angles - probably the spray of cans as they were opened.
No rubber coating has come off anywhere.
Luckily the new Push has the aluminum top, whish is where decksavers usually grab to attach anyway. Shouldn't be a problem I'm guessing.
tarekith
https://tarekith.com
https://tarekith.com
Re: Cover for Push 2
I use a turntable cover. It fits nicely over Push and down the side of the Push sized rotating podium style stand I place Push on.
-
- Posts: 2247
- Joined: Fri Jan 10, 2003 5:28 pm
- Location: Tokyo
Re: Cover for Push 2
Had Decksavers for Push 1 and Maschine and both were money well spent. I'm not sure they need to be quite such a tight fit though, was def a touch of friction going on with the Push 1.
Re: Cover for Push 2
I think the quality has slipped a little myself. I had to get them to replace 2 of my Maschine Studio covers because they were a hair too small to fit properly. Luckily the 3rd one barely fits.
tarekith
https://tarekith.com
https://tarekith.com
-
- Posts: 7
- Joined: Mon Nov 23, 2009 9:33 am
- Contact:
Re: Cover for Push 2
The rubber erosion problem of Push V1 is a well known one, even at Ableton HQ. They said it was an issue with very first numbers of Pushes, not the later versions of V1. So Decksavers are a safe bet on later versions of Push V1, and will be on Push V2.
-
- Posts: 1
- Joined: Wed Nov 18, 2015 10:37 pm
Re: Cover for Push 2
Does the Decksaver Push 1 cover fit on the Push 2? Has anybody tried this?