something like Traktor Beatmasher & channel delay
Posted: Wed Apr 11, 2007 11:54 am
anyone knows for a plugin similar to Traktor beatmasher or channel delay?
cheers
bux
cheers
bux
Ableton Forum
something like Traktor Beatmasher & channel delay
Page 1 of 1
Posted: Thu Apr 12, 2007 6:51 am
anyone?
Posted: Wed Apr 18, 2007 2:02 am
never used traktor, but this may be something to look at (though you need reaktor):
http://www.nativeinstruments.de/forum_u ... beatlookup
http://www.nativeinstruments.de/forum_u ... beatlookup
Beatmasher by a different name
Posted: Fri Apr 20, 2007 8:16 pm
The Beat Repeat effect in ableton is virtually indentical in function to the Beatmasher in Traktor 3!
The controls are a little different, so you'll need to do some experimenting, but this should get you started:
Drag Beat Repeat onto your audio track. Set Chance to 0% and change the mode from "Mix" to "Ins". Toggling the "Repeat" button in BR will perform the same as pressing the "Action" button in BM. Setting BR's Grid knob is the same as adjusting BM's Length knob.
The Gate knob does NOT work identically! If you wish to emulate that, you'll need to adjust both BR's Interval and Gate knobs simultaneously, set your Chance back to 100%, and toggle the Device Activator (power button on top-left of effect) to act like Traktor's Action button.
If you have any midi controllers that allow you to assign CC's to buttons, (e.g. my Trigger Finger) I'd suggest using that feature and midi-mapping that to the Repeat button or Device Activator so you can activate the effect with one button press instead of having to "tap on" and "tap off".
Hope that works for you!
The controls are a little different, so you'll need to do some experimenting, but this should get you started:
Drag Beat Repeat onto your audio track. Set Chance to 0% and change the mode from "Mix" to "Ins". Toggling the "Repeat" button in BR will perform the same as pressing the "Action" button in BM. Setting BR's Grid knob is the same as adjusting BM's Length knob.
The Gate knob does NOT work identically! If you wish to emulate that, you'll need to adjust both BR's Interval and Gate knobs simultaneously, set your Chance back to 100%, and toggle the Device Activator (power button on top-left of effect) to act like Traktor's Action button.
If you have any midi controllers that allow you to assign CC's to buttons, (e.g. my Trigger Finger) I'd suggest using that feature and midi-mapping that to the Repeat button or Device Activator so you can activate the effect with one button press instead of having to "tap on" and "tap off".
Hope that works for you!
Posted: Sat Apr 21, 2007 3:32 am
i have a trigger finger and i use a pad to turn on/off beat repeat. is there a way I can assign the aftertouch function of TF pads so that the harder I press, the more I can change the grid interval?
Trigger Finger + Grid
Posted: Sat Apr 21, 2007 4:58 am
Rat --
You sure can. You'll probably want to set up your own preset with Enigma if you haven't already -- by default most of the presets for the Trigger finger don't send any aftertouch data! The ones that DO send the same controller for all the pads; which is often undesirable.
For a quick and dirty way of getting it running; hit Memory Recall on your trigger finger and then whack pad# P10. Press the Control/Note Mute button until your trigger finger shows "not" on its display. In ableton, midi-learn the grid knob to your pad. Exit midi-learn mode. Press the Control/Note Mute button on your trigger finger again so its red LED turns off.
Voila! The grid amount should change depending how hard you lean on your pad!
In lesson two, we'll cover using the Enigma software to better optimize the messages that your pads send.
You sure can. You'll probably want to set up your own preset with Enigma if you haven't already -- by default most of the presets for the Trigger finger don't send any aftertouch data! The ones that DO send the same controller for all the pads; which is often undesirable.
For a quick and dirty way of getting it running; hit Memory Recall on your trigger finger and then whack pad# P10. Press the Control/Note Mute button until your trigger finger shows "not" on its display. In ableton, midi-learn the grid knob to your pad. Exit midi-learn mode. Press the Control/Note Mute button on your trigger finger again so its red LED turns off.
Voila! The grid amount should change depending how hard you lean on your pad!
In lesson two, we'll cover using the Enigma software to better optimize the messages that your pads send.
Posted: Sat Apr 21, 2007 3:59 pm
hi
first of all thank u for reply...yes i use uc-33 plus ld2 & lv2 from faderfox. i have found something alike beatmasher but im in a search for the delay effect close to one they use in traktor
first of all thank u for reply...yes i use uc-33 plus ld2 & lv2 from faderfox. i have found something alike beatmasher but im in a search for the delay effect close to one they use in traktor
Posted: Sat Apr 21, 2007 7:40 pm
thats great...cant wait for lesson2 pip.
one more question; if i want to launch a clip and do a pressure sensitive effect at the same time (distortion drive for instance) is it possible? or do i need to launch clip with one pad, and do the effect on another
one more question; if i want to launch a clip and do a pressure sensitive effect at the same time (distortion drive for instance) is it possible? or do i need to launch clip with one pad, and do the effect on another