user remote scripts

[RTRT]

heres the text file, tried changing to port 2 but still cant get anything to move -

# Config File for User-defined Instant Mappings

# We assume that the controls on your MIDI controller
# send CCs (except for pads). All controls that do not have
# an explicit channel setting are expected to use the
# global channel. CCs & Notes are counted from 0-127
# and channels from 0-15.

[Globals]
# The channel that the controller should send on
GlobalChannel: 8
# If your controller is connected via USB, replace ControllerName
# with the name of the respective port. Live will then try to
# recognize the ports for you when you select your Instant-Mappings
InputName: SL MkII (Port 2)
OutputName: SL MkII (Port 2)
# If your controller has pads that send notes, you can use them to
# play the visible pads in your DrumRacks. Just replace the -1 for
# the note (and channel) of the respective pad. The arrangement of
# the pads in the DrumRacks is as follows:
# 1 2 3 4
# 5 6 7 8
# 9 10 11 12
# 13 14 15 16
# (If you leave the channel of a pad at -1, Live will assume that
# the pad uses the global channel)
Pad1Note: -1
Pad2Note: -1
Pad3Note: -1
Pad4Note: -1
Pad5Note: -1
Pad6Note: -1
Pad7Note: -1
Pad8Note: -1
Pad9Note: -1
Pad10Note: -1
Pad11Note: -1
Pad12Note: -1
Pad13Note: -1
Pad14Note: -1
Pad15Note: -1
Pad16Note: -1
Pad1Channel: -1
Pad2Channel: -1
Pad3Channel: -1
Pad4Channel: -1
Pad5Channel: -1
Pad6Channel: -1
Pad7Channel: -1
Pad8Channel: -1
Pad9Channel: -1
Pad10Channel: -1
Pad11Channel: -1
Pad12Channel: -1
Pad13Channel: -1
Pad14Channel: -1
Pad15Channel: -1
Pad16Channel: -1

[DeviceControls]
# The Encoders will control the device parameters (you can also
# use knobs or sliders). Replace the -1's with the CCs sent by
# the respective controls on your controller. You can also set
# the channel for each controller if it differs from the global
# channel (if you leave the channel of an encoder at -1, Live
# will assume that the encoder uses the global channel).
Encoder1: 23
Encoder2: 24
Encoder3: 25
Encoder4: 26
Encoder5: 27
Encoder6: 28
Encoder7: 29
Encoder8: 30
EncoderChannel1: -1
EncoderChannel2: -1
EncoderChannel3: -1
EncoderChannel4: -1
EncoderChannel5: -1
EncoderChannel6: -1
EncoderChannel7: -1
EncoderChannel8: -1
# Enter the respective map mode for the encoders here. The following
# map modes are available:
# - Absolute
# - Absolute14Bit
# - LinearSignedBit
# - LinearSignedBit2
# - LinearTwoCompliment
# - LinearBinaryOffset
# - AccelSignedBit
# - AccelSignedBit2
# - AccelTwoCompliment
# - AccelBinaryOffset
# Consult the controller's documentation to find out which mode to use.
EncoderMapMode: Absolute
# Buttons used here are expected to not be toggles (i.e., sending
# value 0 every second time you press it).
Bank1Button: -1
Bank2Button: -1
Bank3Button: -1
Bank4Button: -1
Bank5Button: -1
Bank6Button: -1
Bank7Button: -1
Bank8Button: -1
NextBankButton: -1
PrevBankButton: -1
LockButton: -1

[MixerControls]
# Again enter the appropriate CCs for the respective controls.
# If all sliders use the global channel to send their data,
# you can leave the channels at -1. You can, of course, use
# encoders or knobs instead of sliders.
VolumeSlider1: 15
VolumeSlider2: 16
VolumeSlider3: 17
VolumeSlider4: 18
VolumeSlider5: 19
VolumeSlider6: 20
VolumeSlider7: 21
VolumeSlider8: 22
Slider1Channel: -1
Slider2Channel: -1
Slider3Channel: -1
Slider4Channel: -1
Slider5Channel: -1
Slider6Channel: -1
Slider7Channel: -1
Slider8Channel: -1
MasterVolumeSlider: -1
MasterSliderChannel: -1
Send1Knob1: -1
Send1Knob2: -1
Send1Knob3: -1
Send1Knob4: -1
Send1Knob5: -1
Send1Knob6: -1
Send1Knob7: -1
Send1Knob8: -1
Send2Knob1: -1
Send2Knob2: -1
Send2Knob3: -1
Send2Knob4: -1
Send2Knob5: -1
Send2Knob6: -1
Send2Knob7: -1
Send2Knob8: -1
TrackArmButton1: -1
TrackArmButton2: -1
TrackArmButton3: -1
TrackArmButton4: -1
TrackArmButton5: -1
TrackArmButton6: -1
TrackArmButton7: -1
TrackArmButton8: -1
VolumeMapMode: Absolute
SendsMapMode: Absolute

[TransportControls]
# The transport buttons are also expected not to be toggles.
StopButton: -1
PlayButton: -1
RecButton: -1
LoopButton: -1
RwdButton: -1
FfwdButton: -1

[RTRT]

Have it working now, Not sure what I did Thanks for your help

[longjohns]

oh, then i'll stop looking didn't see that last post, was researching whether absolute was the correct mode for the encoders

hehe

[selector97real]

Hi.

I have "programmed" my user remote script for Xone 1D. The software does recognize that the is a hardware controller assigned to the focussed rack (little blue hand can be seen) but the software does not respond when I turn the assigned knobs. Neither the marco rotaries nor the assigned channel volume sliders. I have checked midi channels and midi setup. Am I missing something. Has anybody else maybe had the same problem in the beginning?

thanks for your answers.

>s97

i am on Mac os-x 10.6.4; Live 8.1.5