I followed these instructions here.
http://www.ableton.com/forum/viewtopic. ... ight=mpd24
I was able to get all the faders and knobs working at one point but once I went in to try and get some pad action everything went to hell and now I'm totally lost. I can't even get it back to when I had the knobs and faders working. I've been messing around and sometimes I can get a few things to work but I can't seem to get all (or even most) of the faders/pads/knobs working.
so by following the instructions for the topic above you should have this right?
thats what it should be right? just like that? akldf;ha# Config File for User-defined Instant Mappings
# We assume that the controls on your MIDI controller
# send CCs. All controls, except the sliders for volume
# and the encoders for device parameters, are expected
# to use the global channel. CCs are counted from 0-127
# and channels from 0-15.
[Globals]
# The channel that the controller should send on
GlobalChannel: 0
# If your controller is connected via USB, replace ControllerName
# with the name of the respective port. Live will then try to
# recognize the ports for you when you select your Instant-Mappings
InputName: ControllerName
OutputName: ControllerName
[DeviceControls]
# The Encoders will control the device parameters (you can also
# use knobs or sliders). Replace the -1's with the CCs sent by
# the respective controls on your controller. You can also set
# the channel for each controller if it differs from the global
# channel (if you leave the channel of an encoder at -1, Live
# will assume that the encoder uses the global channel).
Encoder1: 15
Encoder2: 16
Encoder3: 13
Encoder4: 14
Encoder5: 11
Encoder6: 12
Encoder7: 10
Encoder8: 7
EncoderChannel1: -1
EncoderChannel2: -1
EncoderChannel3: -1
EncoderChannel4: -1
EncoderChannel5: -1
EncoderChannel6: -1
EncoderChannel7: -1
EncoderChannel8: -1
# Enter the respective map mode for the encoders here. The following
# map modes are available:
# - Absolute
# - Absolute14Bit
# - LinearSignedBit
# - LinearSignedBit2
# - LinearTwoCompliment
# - LinearBinaryOffset
# - AccelSignedBit
# - AccelSignedBit2
# - AccelTwoCompliment
# - AccelBinaryOffset
# Consult the controller's documentation to find out which mode to use.
EncoderMapMode: Absolute
# Buttons used here are expected to not be toggles (i.e., sending
# value 0 every second time you press it).
Bank1Button: -1
Bank2Button: -1
Bank3Button: -1
Bank4Button: -1
Bank5Button: -1
Bank6Button: -1
Bank7Button: -1
Bank8Button: -1
NextBankButton: -1
PrevBankButton: -1
LockButton: -1
[MixerControls]
# Again enter the appropriate CCs for the respective controls.
# If all sliders use the global channel to send their data,
# you can leave the channels at -1. You can, of course, use
# encoders or knobs instead of sliders.
VolumeSlider1: 1
VolumeSlider2: 2
VolumeSlider3: 3
VolumeSlider4: 4
VolumeSlider5: 5
VolumeSlider6: 6
VolumeSlider7: -1
VolumeSlider8: -1
Slider1Channel: -1
Slider2Channel: -1
Slider3Channel: -1
Slider4Channel: -1
Slider5Channel: -1
Slider6Channel: -1
Slider7Channel: -1
Slider8Channel: -1
MasterVolumeSlider: -1
MasterSliderChannel: -1
Send1Knob1: -1
Send1Knob2: -1
Send1Knob3: -1
Send1Knob4: -1
Send1Knob5: -1
Send1Knob6: -1
Send1Knob7: -1
Send1Knob8: -1
Send2Knob1: -1
Send2Knob2: -1
Send2Knob3: -1
Send2Knob4: -1
Send2Knob5: -1
Send2Knob6: -1
Send2Knob7: -1
Send2Knob8: -1
TrackArmButton1: -1
TrackArmButton2: -1
TrackArmButton3: -1
TrackArmButton4: -1
TrackArmButton5: -1
TrackArmButton6: -1
TrackArmButton7: -1
TrackArmButton8: -1
VolumeMapMode: Absolute
SendsMapMode: Absolute
[TransportControls]
# The transport buttons are also expected not to be toggles.
StopButton: -1
PlayButton: -1
RecButton: -1
LoopButton: -1
RwdButton: -1
FfwdButton: -1
I was hoping maybe one of you could copy paste your userconfiguration and I could see if it works for me. or would that not work? fuck I am totally out of ideas. could this be a problem with settings on my akai. its pretty new to me so there could be something I'm missing. maybe settings in live? I have two shows next week and I was stoked to use my new toy.
also today is my birthday. please make my birthday wish come true and help me.
thanks. sorry for the rant.