Sample Rate problem- Live 4 rewire slave to Protools

dustinmosley · Post by **dustinmosley** » Thu Jul 29, 2004 5:15 am

I am on a mac G5 in OS 10.3 using Live 4 and Protools 6.4. I am running all my Protools sessions at 24 bit 96 kHz.

When I launch Live 4 as a rewire slave everything comes out at the wrong pitch, when I check the audio setup it says that Live 4 is running as a rewire slave at 44.1 kHz and there are no options that you can change in that menu.

I tried running Live as standalone and setting it to 96 kHz then quitting out and rebooting, then running it again as a slave to Protools but it has the same problem.

Any ideas?

Thanks
Dustin

gives · Post by **gives** » Sat Jul 31, 2004 3:16 am

dustinmosley wrote:I am on a mac G5 in OS 10.3 using Live 4 and Protools 6.4. I am running all my Protools sessions at 24 bit 96 kHz.

When I launch Live 4 as a rewire slave everything comes out at the wrong pitch, when I check the audio setup it says that Live 4 is running as a rewire slave at 44.1 kHz and there are no options that you can change in that menu.

I tried running Live as standalone and setting it to 96 kHz then quitting out and rebooting, then running it again as a slave to Protools but it has the same problem.

Any ideas?

Thanks
Dustin

I wish I knew..This sucks since I am working on a film score and can't figure it out either.. I'll try live 3 for now and see if it works, which I am sure it will..G

gives · Post by **gives** » Sat Jul 31, 2004 8:41 pm

I sent an email to tech support..No response..yet
javascript:emoticon(':(')
I assume they are aware of the Problem. I went back to Live 3 and it works fine after restart..

G

dustinmosley · Post by **dustinmosley** » Sat Jul 31, 2004 11:56 pm

Same story here. I hope they get it fixed soon.

ronwasserman · Post by **ronwasserman** » Mon Aug 02, 2004 4:32 pm

This is a HUGE problem for me as well.

Running PT 6.4. Opened a locked live session (v3) and everything played back in the wrong key...PT at 48kHz Live obviously at 44.1.

Luckily I opened Live 3 and work around this problem.

Hope they fix it soon.

plastikninja · Post by **plastikninja** » Mon Aug 02, 2004 9:46 pm

Same problem here: PT 6.4 24/96 sessions.
Live 3 never complained, but Live 4 fixed at 44.1.
Live 4 Rewire works fine when I run PT at 24/44.1 (obviously)
but doesn't stream at any higher sample rates than 44.1.

Wrote to tech support as well, waiting for response.

gives · Post by **gives** » Mon Aug 02, 2004 11:42 pm

Anyone heard from tech support on the Rewire issues with Live4 in Protools? Never got a response..

I heard that they may all be at some kind of trade show or something..

I think they should have someone fielding suport on such a radical and quick release.

G

dustinmosley · Post by **dustinmosley** » Tue Aug 03, 2004 3:17 am

Hey Guys,

I found out that this is a bug in v.4 and it will be fixed on the next update, within a week or two I think. So don't delete Live 3 yet if you are running Protools at anything over 44.1 kHz. Live 3 still runs well at the other sample rates.

Good luck,
Dustin

ronwasserman · Post by **ronwasserman** » Tue Aug 03, 2004 3:21 am

Dustin! You ROCK!!!!!

Thanks for the update. Easy to wait a week or two.

rw

gives · Post by **gives** » Tue Aug 03, 2004 6:17 pm

Thanks Dustin..

I guess they are on vacation.. I think I should have been repaired before the release..

gives · Post by **gives** » Tue Aug 03, 2004 6:17 pm

Thanks Dustin..

I guess they are on vacation.. I think I should have been repaired before the release..

Matthias · Post by **Matthias** » Fri Aug 06, 2004 1:20 pm

Hi All,

thank you for your reports and sorry for the troubles.
the protools samplerate problem will be fixed with the
next update coming soon...

kind regards,

matthias

gives · Post by **gives** » Thu Aug 12, 2004 2:59 am

Matthias wrote:Hi All,

thank you for your reports and sorry for the troubles.
the protools samplerate problem will be fixed with the
next update coming soon...

kind regards,

matthias

What is the time frame on "coming soon" I need it for a film I am scoring and am not able to use it in the Protools mixed session I am in?

Thanks in advance,

G

Matthias · Post by **Matthias** » Thu Aug 12, 2004 8:16 am

hi Gives,

you can use live as a slave to protools, but because of the
bug only in a protools session with 44.1kHz. Unfortunately
I can not say when the update will be released, perhaps
in about one or two weeks (without any guarantee)

kind regards,

matthias

gives · Post by **gives** » Fri Aug 13, 2004 6:11 am

Matthias wrote:hi Gives,

you can use live as a slave to protools, but because of the
bug only in a protools session with 44.1kHz. Unfortunately
I can not say when the update will be released, perhaps
in about one or two weeks (without any guarantee)

kind regards,

matthias

That won't work for me becuase the film I am doing is has audio at 24bit 48khz and 96khz sample rates.

I look forward eargerly to the update.

Greg

Sample Rate problem- Live 4 rewire slave to Protools

Sample Rate problem- Live 4 rewire slave to Protools

Re: Sample Rate problem- Live 4 rewire slave to Protools

Update

PT 6.4

add me to the list

Rewire Protools still buggy locked at 44.1khz

PT and Live 5

V4Rewire issue 44.1khz